View source for IPsec VPN with pfSense

== About ==
How to setup an ipsec vpn between 2 instances of pfsense using both a static (work) and dynamic ip address (home office). However, a static IP is NOT a requirement.

== Software used ==
* pfSense: https://www.pfsense.org

== Requirements ==
* Dynamic '''OR''' static IP address
* A [https://www.namecheap.com/ domain name] or a [https://www.maketecheasier.com/best-dynamic-dns-providers/ free dynamic DNS provider].
* CPU with [https://en.wikipedia.org/wiki/AES_instruction_set AES-NI] (if your uplink is 20Mbps or faster)

== Configuration ==
I'm going to assume that if you're at this point, you already have a working pfSense configuration at both locations.

Both locations must NOT have the same internal LAN address - meaning both can't be running 192.168.1.x addresses, one can run 192.168.1.x while the other can run 192.168.2.x.

Final note - the VPN configuration on both firewalls will be exactly the same, save for parts that require IP addresses or hostnames.

Let's get started:
* Click on VPN -> IPsec, and on the bottom right, click on the green "'''+''' Add P1" button at the bottom of the screen.
=== Phase 1 ===
==== General Info ====
* Key exchange version: IKEv2
* Internet Protocol: IPv4 (IPv6/Dual stack will work if you're running IPv6 at both sites)
* Interface: WAN (or whatever you named the interface with the public IP address)
* Remote Gateway: this is where you need either your own domain, or a free Dynaimc DNS provider - or manually entering the IP addresses works, users with dynamic IP addresses the "work" location will have to update your IP address manually every time it changes.
** Remote Gateway (home): work.piracyforjesus.xyz
** Remote Gateway (work): home.piracyforjesus.xyz
* Description: put whatever you like or leave blank
==== Phase 1 Proposal (Authentication) ====
* Authentication Method: Mutual PSK
* My Identifier: Distinguished name:
** Home: home.piracyforjesus.xyz
** Work: work.piracyforjesus.xyz
* Peer identifier: Distinguished name
** Home: work.piracyforjesus.xyz
** Work: home.piracyforjesus.xyz
* Pre-Shared Key: On one firewall, click generate key, then copy & paste that key to the other firewall

==== Phase 1 Proposal (Encryption Algorithm) ====
* Encryption Algorithm:
** Algorithm: AES128-GCM
** Key Length: 128 bits
** Hash: SHA256
** DH Group: 14 (2048)
* Lifetime (Seconds): 28800
==== Advanced Options ====
Leave everything defaulted in this section, and click Save. When finished, it should look like this:

[[File:Phase1-complete.png]]

=== Phase 2 ===
From the above screen, click on "Show Phase 2 Entries (0)" and expand out the menu, then click on the green "'''+''' Add P2" button that appears.
==== General Information ====
* Mode: Tunnel IPv4
* Local Network: LAN subnet
* NAT/BINAT translation: None
* Remote Network: Network
** Address (Work): 192.168.10.0/24
** Address (Home): 192.168.1.0/24
* Description:
** Home: Work LAN
** Work: Home LAN
==== Phase 2 Proposal (SA/Key Exchange) ====
* Protocol: ESP
* Encryption Algorithms: AES128-GCM @ 128 bits
* Hash Algorithms: AES-XCBC (or SHA256 if your CPU doesn't have AES-NI)
* PFS key group: 14 (2048)
* Lifetime: 3600
==== Advanced Configuration ====
* Automatically ping host: set this IP address to a server you run 24/7, this will keep the VPN up 24/7

After you hit save, this is what your Phase 2 will look like:

[[File:Phase2-complete.png]]
== Firewall Rules ==
After you hit "Apply Changes" on both firewalls, your IPsec VPN should connect right away. You may find that you can't ping anything across the VPN though - you'll need to click on Firewall -> Rules -> Add to create a hole in the firewall to allow traffic to pass.
=== Insecure allow all traffic rule ===
This rule will allow ALL traffic to traverse the firewalls (remember you have to make the same rule for both sides). This is NOT a secure setting! If your home network gets compromised, your home network can be a jumping off point for bots/hackers/viruses to invade the network on the other side of the VPN.

''' You have been warned.'''
==== Edit Firewall Rule ====
* Protocol: Any

And that's it, unless you want to add a description. End result looks like this:

[[File:IPsec-any-rule.png]]